Introduction: This guide explains how SMS Caster and SMS Deliverer connect a computer to a multi-port SMS modem pool and turn imported numbers into port-based sending tasks.
A multi-port SMS modem pool is not a single device that magically sends messages. It is a group of cellular modules behind one USB connection, and the computer must discover each module as a separate serial port before any bulk SMS job can begin. The software layer — SMS Caster or SMS Deliverer — gives the user a way to see those ports, assign SIM cards to them, and push messages out through AT commands. Understanding how the software, serial ports, and hardware cooperate makes the setup far less mysterious, especially when a job is queued but nothing leaves the modem. this guide walks through that connection flow step by step.
When a multi-port SMS modem pool connects over a single USB cable, the host computer typically sees a set of virtual COM ports on Windows or /dev/ttyUSB ports on Linux. Each port represents one cellular module and one SIM slot inside the pool. For example, a 16-port 4G LTE modem pool can appear as sixteen separate serial devices, all sharing one USB link. The software does not treat the pool as one giant modem. It works port by port, because each SIM card has its own registration state, signal level, and message queue. On Android hosts, the same idea applies through the platform's serial or USB communication layer. The serial-port layer is the bridge. It carries AT commands from the software to each module and returns status responses. 3GPP TS 27.007 defines many of the standard modem control commands, while 3GPP TS 27.005 covers SMS-specific command behavior in text and PDU mode. A program such as SMS Caster or SMS Deliverer scans the available ports, opens a connection to each one, and checks whether a SIM is present, registered, and ready. The ArchWiki mobile broadband modem page describes this general pattern for Linux: a USB modem exposes serial interfaces, and user-space tools manage connections and commands. The hardware layer simply executes those commands on the cellular network. YX multi-port SMS modem pools follow this model with 8-, 16-, 32-, and 64-port variants, single USB connection, AT command control, and support for Windows, Linux, and Android hosts.
Once the ports are visible, the software becomes the control center for the bulk SMS job. The workflow is easier to follow as a sequence, because each stage answers a different question: what to send, which port sends it, when it goes out, and what happened afterward. SMS Caster and SMS Deliverer are supported software references for this connection flow, and they both rely on the serial ports and AT commands described above. The four stages below show how imported numbers become real port tasks.
The key point is that SMS Caster or SMS Deliverer does not send one giant blast. It turns the imported list into many small port-level tasks, each tied to a serial port and a SIM card. That port-level view is what makes a multi-port pool useful for bulk SMS work, because the user can see exactly where each task is going.
Bulk SMS speed depends on more than the number of ports. Every port has a live status: online or offline, registered or searching, strong signal or weak signal. The software reads this status through AT commands before and during a campaign. If a port is offline, the task waits or moves to another port. If a SIM card has no balance or has reached its carrier limit, the message will not leave the modem, no matter how well the software is configured. This is why SMS Caster or SMS Deliverer often shows per-port indicators rather than one overall progress bar. SIM balance and carrier service are user-provided parts of the setup. The modem pool hardware does not include free messaging or prepaid credit. A user must insert active SIM cards and pay the carrier's message fees. When those SIM cards have different balances or plans, the software can distribute the workload to keep the campaign moving. For example, a 64-port 4G LTE modem pool with 64 SIM cards can spread a large list across many channels, but the real throughput still depends on network congestion, signal quality, and message length. the listing figure of around 3,600 SMS per port per hour is a theoretical reference; actual results vary with the carrier and radio conditions. Checking port status and SIM balance before a bulk send is therefore a practical habit, not a technical formality.
SMS Caster and SMS Deliverer setup works best when the user understands the three layers involved. The software layer manages lists, tasks, and logs. The serial-port layer gives each modem module its own COM or tty address. The hardware layer executes AT commands and sends messages through user-provided SIM cards and carrier service. Once the ports are discovered and assigned, a bulk SMS job becomes a set of port-level tasks rather than an unpredictable black box. For readers who want to go deeper, the YX product reference shows how 8-, 16-, 32-, and 64-port pools are organized, and the linked standards explain the AT command background. The next useful step is simply to review the port count, host operating system, and SIM plan that match the intended workflow.
A:SMS Caster connects by opening the serial ports that the pool exposes after the single USB link is active. On Windows these appear as COM ports; on Linux they appear as ttyUSB devices. The software scans those ports, sends AT commands to check SIM and signal status, and maps each port to a SIM slot so the user can assign sending tasks.
A:Both are supported software references for connecting to and managing a multi-port SMS modem pool. They share the same underlying connection path: serial ports plus AT commands. SMS Caster is often used to configure ports, manage SIM slots, and organize outbound tasks. SMS Deliverer also handles SMS delivery workflows. The practical difference depends on the version and features chosen, so users should match the software to their operating system and campaign needs.
A:No. The software is the control layer, not the radio network. A multi-port SMS modem pool needs active SIM cards inserted by the user, and the mobile carrier charges for each message according to its plan. SMS Caster or SMS Deliverer can queue and route messages, but they cannot replace SIM cards or pay carrier fees.
Mobile broadband modem - ArchWiki